Second Attempt at Installing GPR Stabilizer and Failed..Again. What am I Doing Wrong?

The post keeps sliding on the neck of the frame. The first time I kind of just put

it on there not knowing there was a certain way of doing it. It slipped... of

course. The second time I actually installed it according to the GPR's

instructions online. I thought I did it right. Well, I put the damper on the highest

setting and jerked the handle bars, and it slipped right off. Is there something

I'm missing? I'm starting to question how strong this set up is...especially in

race situations. Does anyone weld these posts to the frame? I'm lost...:busted:

BTW, it is a 2006 YZ450F. Thanks in advance.

I had the same problems, I never was able to get it to where the post wouldnt move. I ended up selling mine when the Scotts came available, it has a tab that mounts to the gas tank bolt, much better set up.

If the GPR lacks the tab for the gas tank bolt, I can't fathom how anyone might imagine it would stay put on the new frame.

If I remember correctly, the mount had a set screw on each side that was to tighten up against the steering head, mine was bought when the 06 first came out, they may have changed something by now.

If I remember correctly, the mount had a set screw on each side that was to tighten up against the steering head,
Oh, I like that idea. Lets distort the bearing pocket! :busted:

Yep...I had one on my '06 like that. I absolutely hated it. I was too afraid to have the pinch bolts they provided dig into the stearing head too much. Its a pretty bad design if you ask me, not nearly enough security having it bolted on.

I think thats an easy answer. Mine has two small set screws on the sides of the post clamp. The set screws and not damaged my Steel neck. I believe you have an alum one. I am not sure if distorting will happen on it but I highly doubt it. Remember this is not cranked down on the neck. Just snug, with lock tight to prevent back out... I drilled a small pilot notch for the set screw to lay it.

You might ask Scott's' if they have one with the set screws in it.

You might ask Scott's' if they have one with the set screws in it.

They don't. Theirs is a clamp design with a tang extending back over the the frame to the bolt that holds the front of the gas tank. Since the steering head "tube" of the aluminum YZF is not actually tubular, the shape of the clamp section that fits over the head has to be machined to fit, and can only clamp on 3 sides of it. The tang anchors the assembly, and keeps it from shifting forward, or scrubbing side to side on the steering axis.

I just got mine. I'll put up a picture tomorrow.

I had the same problem(06YZ)........I finally got it to stick by following their instructions exactly.....which is: tighten the pinch bolt a tiny bit, followed by the 2 set screws a tiny bit, then the pinch bolt again and so on until tight. Basically you have to tighten the 2 set screws and the pinch bolt all evenly.

I also drilled 2 tiny divots to accept the set screws.

I would be interested in another type of post if someone knows of one?

weld a tang on it and be done.

on my 06, even the scotts was not right. the tang was not on the mount correctly. so i cut it off, bolted it in place, did 2 tack welds and then welded it up correctly off the bike. has not moved since!

Can you post a picture so we can see what your saying??

Sounds like a good idea!

So, what's the verdict?

You tell us.....Did you get it to stick?

You tell us.....Did you get it to stick?

Even if I do get it to stick, I'm not sure that I'll trust it during a race.

Will the Scott's mount fit my GPR damper?

Someone mentioned it mounts to the tank mount. Will it accommodate an IMS 3.1 gal tank?

What do you mean by "tang"?

Even if I do get it to stick, I'm not sure that I'll trust it during a race.

Will the Scott's mount fit my GPR damper?

Someone mentioned it mounts to the tank mount. Will it accommodate an IMS 3.1 gal tank?

What do you mean by "tang"?

Yes it will work with the IMS tank, I have one on my 08. I dont think the mount will work with the GPR, if I remember correctly the slot in the GPR arm is larger than the Scotts pin. The Scotts mount has a tab welded to the back of the bracket that comes down and mounts to the bolt where the tank bolts down. You may be able to get on Scotts website and see the bracket, if not chech BRP 's website.

Thanks.

Does GPR have a mount kit designed to be welded on the frame? I would rather have a shop do it right.

Here's the Scott's mount. I haven't gone into mounting it yet because I'm waiting for an updated top head bearing to do it all at once.

2923554078.jpg

Well my GPR post popped off the frame in a race :thumbsup:

Anybody have a solution to get the post to stick, maybe weld it to the Front Fuel Tank mount?

What does GPR say about this - it sounds real chinsy to me. I have never had any issues with Scotts mounts on 03-05s

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!


Register a new account

Sign in

Already have an account? Sign in here.


Sign In Now