Questions about the footpeg mod.

I did the footpeg mod and I really like the extra room it gives me on my 450. But! I recently came up short on a jump and broke my lower leg on the kick start side, my foot may have come off the peg (I'm not really sure). My question for you guys is-- Now when I look at the peg on the kick start side it does not look level. It slopes down (it is lower on the back edge than it is on the front edge) I never noticed it before. The peg does not look broken, bent or loose, it just does not look level(the peg on the other side does look level). Will someone that has done the mod on a 450 let me know what their's look like? I haven't pulled the peg off yet (few more weeks of recovery yet) but I've spent the last couple of weeks wondering what happened and am wondering if the peg broke/bent before or after the crash or if the peg was always like that. Thanks guys.

I did the footpeg mod over a year ago. Both of mine are level. I think maybe the crash (or a previous crash) bent the peg.

Thanks for checkin'.

I did the footpeg mod over a year ago. Both of mine are level. I think maybe the crash (or a previous crash) bent the peg.

Ditto

If you broke your leg on that jump then you must have hit hard enough to bend or tweek the peg mount.

I would look over that welded mount real close, I would bet you have damage there

Thanks guys,I will look at it closer as soon as I get a little more mobile. Part of the problem is that it wasn't even a harsh landing (I never even crashed) It felt like my right heel made contact with the ground before the bike did, but I'm not really sure. I think my foot was on the peg but only in the toe area and not the arch (or middle). It's been just about a month since the break and I'm going crazy! With boredom.

Has anybody noticed their kickstart gets a hammering after doing this mod. The kickstart hits the teeth of the peg and smashs the S$#! out of it, anyone know a fix ???? :thumbsup:

Has anybody noticed their kickstart gets a hammering after doing this mod. The kickstart hits the teeth of the peg and smashs the S$#! out of it, anyone know a fix ???? :thumbsup:

I haven't done any mods and my kickstart gets a hammering :devil:

Though it has on every F-bike I've owned, just a little less on the 450 cause it starts without the snake charming ritual the others did :awww:

john407 you might have got your foot or heal under the frame rail and the biek smashed it on the ground.

I did something like that once but all I got was a badly sprained ankle. Had to wear my boot all the way home (3 hrs) cause I was afraid to take it off!!

Hope you heal quickly.

i noticed that the pegs looked off when i first saw the bike in the showroom. i looked at another and it was the same. i don't know if it was just the way i was looking at it but, none of them looked symetrical. even on my 426 one was tweaked just a little.

What is the "Foot peg Mod" being referred to?

What is the "Foot peg Mod" being referred to?

Moving the peg back and down about 3/4 of an inch over all. To do this your simply follow these steps

1: Swap Springs righ to left

2: Cut Barrol on Peg off (Hack Saw)

3: Debur (Very Well)

4: Weld (Not needed)

5: Grease pin well

6: Install New Mod

A must for Tall riders

Modpeg.jpg

If you are lazy and looking for the same result you can invest in some fastway footpegs.

If you are lazy and looking for the same result you can invest in some fastway footpegs.

:thumbsup:

It Took me a whole 20 minutes to do this mod

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!


Register a new account

Sign in

Already have an account? Sign in here.


Sign In Now