motoxjeff

2014-17 YZ450F Picture thread! Share yours!

477 posts in this topic

Gave the 4fiddy a makeover whilst i cant ride,

- Talon/Excel wheel set

- Braking batfly 270mm front disk kit

- Braking rear wave disk

- New plastics

- New graphics

- New full Pro Circuit Ti-6 pro system

Can't wait to ride the beast!!

1451283407407.jpg

1451283472228.jpg

1451284240512.jpg

2 people like this

Share this post


Link to post
Share on other sites

2015 YZ450f

ARC levers

Hammerhead brake and gear levers

Renthal bars

Braking 270mm front rotor

Full Akrapovic exhaust system

Funnelweb filter

SM pro platinum wheels

Hinson clutch cover

Plus other bling

MPE suspension

Mainly use this bike for trail riding and social mx. Love this bike!!

"social mx"? Is that like saying "I'm a social drinker"? I respect your self control. I've been battling MX addiction since I was a kid. I was introduced to it in my teens. It's not my fault though I was born with it.
4 people like this

Share this post


Link to post
Share on other sites

Norwegian bike :)

Braking oversize rotor kit, renthal grips, cycra powerflow plastic kit with cycralite front fender and jgr graphics.

Studded tires is a must in the winter ;)

Bought the GYTR power tuner but haven't tried it out yet with different mapping...

1451989399249.jpg

1451989418907.jpg

1451989472382.jpg

1451989500050.jpg

1 person likes this

Share this post


Link to post
Share on other sites

ImageUploadedByThumper Talk1456834547.803842.jpg

Got a little ride in yesterday evening, February 29th in Newfoundland, Canada. This doesn't happen normally unless you have studs.

Who would have thought it would be better going on dirt bike than sled in February?!

ImageUploadedByThumper Talk1456834730.811247.jpg

Share this post


Link to post
Share on other sites

Assuming 2016s aren't example from this thread. Just picked her up two weeks ago. Still snow here in Michigan so just building her up before riding season begins.ImageUploadedByThumper Talk1457185076.046875.jpg

ImageUploadedByThumper Talk1457185088.667355.jpg

ImageUploadedByThumper Talk1457185107.277127.jpg

ImageUploadedByThumper Talk1457185149.514728.jpgImageUploadedByThumper Talk1457185177.195885.jpg

2 people like this

Share this post


Link to post
Share on other sites

Subscribed.


Assuming 2016s aren't example from this thread. Just picked her up two weeks ago. Still snow here in Michigan so just building her up before riding season begins.attachicon.gifImageUploadedByThumper Talk1457185076.046875.jpg
attachicon.gifImageUploadedByThumper Talk1457185088.667355.jpg
attachicon.gifImageUploadedByThumper Talk1457185107.277127.jpg
attachicon.gifImageUploadedByThumper Talk1457185149.514728.jpgattachicon.gifImageUploadedByThumper Talk1457185177.195885.jpg

What bend are those bars?

1 person likes this

Share this post


Link to post
Share on other sites

Assuming 2016s aren't example from this thread. Just picked her up two weeks ago. Still snow here in Michigan so just building her up before riding season begins.attachicon.gifImageUploadedByThumper Talk1457185076.046875.jpg

attachicon.gifImageUploadedByThumper Talk1457185088.667355.jpg

attachicon.gifImageUploadedByThumper Talk1457185107.277127.jpg

attachicon.gifImageUploadedByThumper Talk1457185149.514728.jpgattachicon.gifImageUploadedByThumper Talk1457185177.195885.jpg

More info on this bike is needed ahaha. Graphics?

1 person likes this

Share this post


Link to post
Share on other sites

More info on this bike is needed ahaha. Graphics?

sorry for the late reply ha. The bars are renthal fatbars, RC high bend. Graphics are a combo of factory fx 2016 kit and decal works number plates. Here is the most recent pictures.

ImageUploadedByThumper Talk1458236020.483357.jpg

ImageUploadedByThumper Talk1458236048.577724.jpg

ImageUploadedByThumper Talk1458236069.855448.jpg

1 person likes this

Share this post


Link to post
Share on other sites

never mind... i can't figure out how to post my pic

 

i figured it out... lol 

 

at first i was trippin out on the yellow plastics and graphics but maybe i'll get used to them

Edited by Turbolife

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!


Register a new account

Sign in

Already have an account? Sign in here.


Sign In Now

  • Similar Content

    • By Bermat
      Hi there,
      I just bought a Keihin FCR (I don't know if it is a 39,40 or 41mm) taken from a 2004 YZ450F motocross. I would like to know exactly whatI have to buy to make this fit on my drz, and how to know if it is a 39,40 or 41mm. Also, I would like to know which jet I should buy according to this : 500ft over sea level, 3x3 mod, MRD exhaust, KN air filter. Here are some picture of the carb.
       
      Thank you for your help !!
       




    • By CallMeAnsel
      I just finished adjusting the rear sag on my Yz450f, but I'm not sure about one thing. I lowered the bike a few inches and I noticed that the spring feels loose when the bike is on the stand. I'm able to freely move the spring around when the bike is on the stand, yet when the bike is off the stand the spring doesn't move at all. I now feel comfortable, but did I lower the bike too much? Is this normal? Should I raise the bike to add some tension in the spring? Thanks for any advice.
    • By MotoXRacer_19
      I'm caught between a rock and a hard place. My 2010 KTM 250 XC won't stop peeing coolant out of the overflow tube. I've used 3 different radiator caps (two of the oem 1.8 bar caps and one CV4 2.0 bar) and it still continues to pee coolant as soon as the bike starts up. I just recently bought and installed brand new radiators [GPI on eBay for $88 (the seem fine just the welds are a bit crappy and you can see inside of the tubes where the metal from the welds drooped down but there are no blocks)] and silicone hoses (profactory hoses) thinking they were the problem since the old radiators were bent in like bananas. To my dismay that was apparently not the issue. I've had everything apart and looked at. Has brand new base gaskets, head gaskets, radiators, and radiator hoses. I've bled the radiators like the manual says and there are no bubbles like air leaking into the system or being in the system. The jetting is also perfect. The only thing I haven't changed out is the oem impeller in the water pump but it looks to be in great condition. Any ideas on how I can fix this problem before it gets worse? Also, has anyone else had this problem and figured out how to fix it?
      I ride it in mostly tight 0-10 mph trails and also some 10-20 mph trails. 
    • By TheHumbleBraap
      Hello great people of thumper talk. Well I've been having some problems with my old 2002 YZ250F. I was riding a few days ago when my bike just sputtered to a stop almost like it ran out of gas. Well gas was not the problem and I couldn't get her to run she would only fire for a second then die. I found that one of my TPS wires snapped, so I figured the reason it wasn't running was because of that wire. After soldering it back together it was still doing the same thing, so I just left it for the night. When I came back the next day whilst kicking it over I noticed all of a sudden the kicker stopped. the motor was seized. I tried turning the crankshaft at the flywheel and it would not budge forward at all but it would turn backwards or clockwise, so from here I figure I'll start taking the bike apart and figure out whats locking it up. Once I removed the cylinder head I was at a surprise when I saw this relatively large piece of brass sitting on top of my piston. I was thinking where in the hell did that come from. It was getting too late for me to go any further tonight, so I figured I would post a picture on here to see if anyone can tell me what they think this piece may go to. Is it something in the crank maybe up by the valves, from the carburetor I have no idea. It just amazes me that the piece is so intact since it was sitting on top of my piston. Also after that I did try turning the crank again, and it did turn but it felt horrible. It was very clunky and it sounded like shit might be grinding in there so I stopped. Well thanks for taking a look and if you have any insight as to where that piece might have come from please let me know. Other than that I'll be breakin her down further tomorrow.
    • By fergussmyth
      Hi all,
      I have had my 1978 SR500 is storage for 13 years and over the last year I have done a base restoration but yet to do any work on the motor. The bike was running well last in use  (13 years ago). I have recently got it stated and noticed it is running extremely hot and backfiring, the idle speed also varies a fair bit. i have had the carb cleaned and put a new air filter in but both didn't seem to make a difference. would anybody have any suggestions how to fix this problem.
      would love your thoughts. cheers