Knockin 426

11 replies to this topic

Posted September 13, 2001 - 01:23 PM


I have a 2000 426 that knocks at idle and quits as you rev the engine. I have checked the valves and they are fine. Is this normal for this engine? It runs fine but the knock has me worried. Any feed back will be appreciated.

  • dirtbikebd

Posted September 13, 2001 - 01:42 PM


To me when you talk about knocking in the motor it is a gas thing, what kind of gas do you use? Like in Cali it is 91 now, before it was 92 octane, so I am using an octane booster. I know the manual says to use 95 octane. I think I may use octane booster in my streetbike because ever since octane rating has gone down, it is running like crap as well.

  • yzf

Posted September 13, 2001 - 02:58 PM


does the noise change when you pull the clutch in? where does the noise sound like its comming and from and what does it sound like take a good listen

  • rjpyne

Posted September 13, 2001 - 04:11 PM


Originally posted by KANSAS:
I have a 2000 426 that knocks at idle and quits as you rev the engine. I have checked the valves and they are fine. Is this normal for this engine? It runs fine but the knock has me worried. Any feed back will be appreciated.

I've heard that the Canadian models tend to start this noise after about a year of normal noise and then they blow up after a few rides. Be Careful and get it to the dealer! Just kidding, this is Rob, it's about time you found this website. Hopefully someone will be able to help you. Send me an email at
PS I will be coming out to Utah soon so we can attack Cherry Creek some more.

  • Howard_Huge

Posted September 13, 2001 - 06:54 PM


My 00' 426 has similar if not the same symptoms. Haven't got it to the dealer yet. When I was in Colorado I had Larry Roseler listen to it (really) and he recomended that I not ride it on the CO. 500, so I rode a backup bike instead. He also said to send the motor to him and he would fix her up asap. How long has your motor been making the knocking noise? I seem to think its due to low oil pressure at idle because as soon as you rev it up a bit the knocking goes away. My 2 cents and some change.

Interesting, Huge

  • mxchamps

Posted September 13, 2001 - 07:16 PM


I ride with Kansas and think he did a crappy job at explaining the noise(no offense Kansas). It is a rattle/knock coming from the left(I think) side of the engine. It does it at low RPMs like he said, in gear or out of gear, clutch in or clutch out. I am pretty certain it is not in the transmision but rather in the head or cylinder. This is just my impression of the noise. could it have anything to do with the timing chain? Any ideas? Bt the way, that was a good one Roberto!

Visit the ThumperTalk Store for the lowest prices on motorcycle / ATV parts and accessories - Guaranteed
  • DOC

Posted September 13, 2001 - 08:05 PM


I'm thinking it is the natural mechanical noise the bike develops after some time. My friends 426 sounds like that at idle, and im sure many others do. Huskys and some KTM's make the same kind of noise. Guessing these engines were not built to run quiet as possible, because that wouldn't be a major consideration for the bikes intended purpose. Just my uneducated opinion.

  • holeshot

Posted September 13, 2001 - 09:31 PM


Some have had the key in the crank drive gear (counterbalancer drive gear?) develop slop and make a knocking noise on their '00.
Yamaha got rid of the key and went to a spline in '01.

This problem hasn't surfaced on my '00 (yet).

Holeshot's Page

[This message has been edited by holeshot (edited September 14, 2001).]

  • oldnbold

Posted September 14, 2001 - 03:46 AM


I would look 1st at the keyway on the counterbalancer drive. Many threads about this problem some time back. My '00 developed a knock but the symptoms persisted throughout the rpm range (you could hear the knock better at idle). Upon inspection of the counterbalancer drive gear, there was noticable slop. A new key, some red loctite, and a lot of torque to the nut and the problem hasn't returned in over a year.

  • Scott_F

Posted September 14, 2001 - 04:55 AM


Bingo! These two guys got it. A search for CB gear will fill in the details.

  • Howard_Huge

Posted September 20, 2001 - 03:08 PM


SWEEETT, I hope thats all it is. How hard is it to replace the key. I will look at the archives maybe my answer is there.
thanks, huge

  • Dave_S

Posted September 21, 2001 - 07:32 PM


I just finished a CB key job on my bike about an hour ago.

It was making all kinds of funny noises and you cant really tell where they are comming from, sometimes it goes away when it warms up, sometimes it gets worse when it gets hot.
I was getting pretty worried about it last week so I tore into it tonite before going to the track tomorrow. Took about maybe two hours as I took my time, not a hard job. When i got the side cover off, I could feel the slack in the CB drive gear. Not a lot but it was there. The key had been wobbling and was grooved on the sides. Didnt have a spare key but it is square so I just cleaned it up and turned it 90 degrees. Fired it back up and it not a peep from the engine other than the exaust! Yipee!

Fortunatly I consulted the manual to see what direction one of the gears went on becuase if I hadnt, I would not have realized that the CB gears must be aligned to each other by a dot mark.

I remember someone saying they made keys out of some hardened bar stock. Who was that and how has it worked out?

Dave S

Related Content


Snake pit oct 30th by The Anvil

Dirt Bike   Dirt Bike Regional Discussion   California
  • Hot  106 replies

100 hrs on 2014 yz450f, shim valves or replace them? by ttr230rider6

Dirt Bike   Make / Model Specific   Yamaha   YZ 400/426/450
  • Hot  79 replies

Michigan Motocross Tires by 288yz450

Dirt Bike   Dirt Bike Regional Discussion   North
  • 1 reply

yz400f throttle bog by yz400fmaniac

Dirt Bike   Make / Model Specific   Yamaha   YZ 400/426/450
  • * * * * *
  • Hot  28 replies

First Hare scramble tips by dhend8

Dirt Bike   General Dirt Bike Forums   General Dirt Bike Discussion
  • Hot  33 replies

Join Our Community!

Even if you don't want to post, registered members get access to tools that make finding & following the good stuff easier.

If you enjoyed reading about "" here in the ThumperTalk archive, you'll LOVE our community. Come join ThumperTalk today!

The views and opinions expressed on this page are strictly those of the author, and have not been reviewed or approved by ThumperTalk.