226 replies to this topic

[Eddie Sisneros]

i get so many requests for this im posting it here to list in my products-

48-50hp requires-

Cylinder Works big bore kit
39mm fcr carb kit
Hotcams stg1 in and ex
MRD/SSW pipe

if you send me a motor that the valve train is in good shape with low hours/miles we build this set up for $1899.95 shipped back to you.

valve train parts add to the cost.

please email or call for a individual qoute. this post is for reference purposes. prices may fluctuate.

thanks!

[hyper7driver TT Silver Member]

Think you could do this to my wife's DR200?

[UrbanTerror TT Silver Member]

Wow, just paid that price for just the parts and I could have saved all the build blues.

Not a bad deal.

[707drz A Legend in his own mind]

i guess now em going to have to save up my christmas bonus and put a hold on the SAS swap on the rig..

[Craigo 485sm Get Help Now]

$1899.95 is amazing value..if you add up the retail price of the bits and shipping (to U.S only I presume)...Eddie is doing it for next to nothing......

[rider428 TT Bronze Member]

what type of dyno results would I get using the stock 2000 E model exhaust with this setup?

[Craigo 485sm Get Help Now]

Low/mid 40's hp without SSW/MRD

[omgshesaboy TT Bronze Member]

This is HP to the wheel correct?

[707drz A Legend in his own mind]

omgshesaboy said:

This is HP to the wheel correct?

yes:thumbsup:

[shuswap1 TT Bronze Member]

Very interesting....but how loud is the pipe?

We're getting increased enforcement around here and the upper end limit is 95db.

My full Jardine is likely louder than that, but I like to know if I have to avoid tests with the SSW pipe as well.

Last question: How much power would I lose if I stuck with my Jardine, but went with the rest of the package

Edited by shuswap1, 07 October 2011 - 09:24 PM.

[Craigo 485sm Get Help Now]

Noise level will be more than 95db.....

With your pipe you will  have a healthy mid range, but the top end won't be there without the SSW/MRD...(or yosh ti)

[fragmasterkarl TT Bronze Member]

Not build by eddie but basically the same setup :-)



DRZ440SM Dyno Run - 48.15 BHP - 33.59 Torque





















.

[buzzski TT Member]

Eddie Sisneros said:

i get so many requests for this im posting it here to list in my products-

48-50hp requires-

Cylinder Works big bore kit
39mm fcr carb kit
Hotcams stg1 in and ex
MRD/SSW pipe

if you send me a motor that the valve train is in good shape with low hours/miles we build this set up for $1899.95 shipped back to you.

valve train parts add to the cost.

please email for a individual qoute. this post is for reference purposes.

thanks!

What compression is the piston

[buzzski TT Member]

What compression is the piston in this set up

[Smias Απλά γαμάτος!!!]

12-12.2:1 , with a single layer base gasket .

[Bobbed06 TT Silver Member]

I run this complete setup and it will pull 4th gear power wheelies with 15-46 gearing on an S. Good stuff

[buzzski TT Member]

What compression is the piston in this set up? Oops didnt see the 2nd page two too many posts

[buzzski TT Member]

Is that the only compression cyclinder works offers? (12.2:1)

[whitsdurz TT Bronze Member]

I already have a yosh ti, and now yosh graphics...  how about the kit price minus the 'zaust?

[707drz A Legend in his own mind]

Hey Eddie for the ones that already have the MRD or yoshimura Ti but need the valve train re built on there high mileage DRZ what would the basic package be for

The said above minus pipe with rebuilt head assuming it needed nothing else. To give the guys that have a pipe already an idea