FrontBrake Cable Routing Question



6 replies to this topic
  • Ga426owner

Posted May 15, 2001 - 09:45 PM

#1

I want to run CR Brake cable routing on my 426. I have the Fastline YZ/CR routing cable.
Any ideas on the Bracket for the lower fork guards? I have had DSP on order forever, with no eta. I know i can use my existing metal cable bracket, but want something that looks/functions better. Does anyone have other options or ideas for this? Or does anyone have phone# for DSP, they have changed their website for no communication. I would like to use my stock lower fork guards if possible/

  • Boit

Posted May 15, 2001 - 02:18 PM

#2

Surfn'Turf Racing has a CR style routing bracket that can be mounted on the stock guards. It's an adequate bracket but isn't what I would describe as top quality. I'm using one on my Carbon Fiber Works fork guards because the one they supplied pulled a chunk of the guard with it when the area it was clamped to detached. The quality of the Carbon Fiber Works units are sub-par, in my opinion. They won't get any more of my business.

  • YZ400Court

Posted May 15, 2001 - 02:25 PM

#3

Try piper peformance (623)587-7708. They have really nice anodized ones for $18.95.

------------------
Pretend it's flat and give it the gas.

Visit the ThumperTalk Store for the lowest prices on motorcycle / ATV parts and accessories - Guaranteed
  • Ga426owner

Posted May 16, 2001 - 06:00 AM

#4

YZCourt, appreciate the info. Does this cover the existing 2 square holes on top of the lower fork guards?

  • Sandracer_uk

Posted May 16, 2001 - 06:14 AM

#5

i found that running the cable between the clips then drilling a small hole in each plastic clip and routing a single strand of safty wire looks fine

  • racer629

Posted May 18, 2001 - 07:19 PM

#6

Best thing to do, is to use two pieces that make up the clamp at the bottom of the fork leg. Move them up to the bottom plastic loop. It is just a bit too wide to drill two holes in the tab, so I suggest drilling one, and letting it hang down just a little bit. Cut the curved piece off, so just a 1/2 in of plastic is available, and run two small 6mm bolts through it. (only one going through the plastic) Looks just like the setup on the CR's, and works just as good. I run that on both of my bikes, 426 and 250F. I'll try and post a picture tomorrow.

------------------
Mr. Wizard says: "Go BIG, or go home!"

  • Ga426owner

Posted May 19, 2001 - 05:05 AM

#7

Racer629 thanks for the assist





Related Content

Forums
Photo

First Hare scramble tips by dhend8


Dirt Bike   General Dirt Bike Forums   General Dirt Bike Discussion
  • Hot  33 replies
Forums
Photo

Snake pit oct 30th by The Anvil


Dirt Bike   Dirt Bike Regional Discussion   California
  • Hot  293 replies
Forums
Photo
Motocross

Thinking about Yamaha 250... by Arctic Pride


Dirt Bike   Special Interest Forums   Pro Racing
  • Hot  491 replies
Forums
Photo

Megabomb Fitment by 288yz450


Dirt Bike   Make / Model Specific   Yamaha   YZ 400/426/450
  • 1 reply
Reviews

Yamaha YZ450F 2017 by Chris.GVS


Yamaha YZ450F 2017
  • - - - - -
  • 0 reviews
 
x

Join Our Community!

Even if you don't want to post, registered members get access to tools that make finding & following the good stuff easier.

If you enjoyed reading about "" here in the ThumperTalk archive, you'll LOVE our community. Come join ThumperTalk today!

The views and opinions expressed on this page are strictly those of the author, and have not been reviewed or approved by ThumperTalk.