Fouling plugs on my YZ 426 F


4 replies to this topic
  • DeepSeaJohnny

Posted January 23, 2011 - 07:05 AM

#1

I bought an 01 YZ 426 a couple of months ago, and it has started to foul plugs rapidly. The bike runs great when it runs, but as soon as I stop it won't kick back up again.
The other day I took it out and rode for about two solid hours. After taking a break the bike wouldn't start, and the obvious answer was a fouled plug. I did a field cleaning because I didn't have a spare (I didn't have the spark plug wrench needed either, but thats it another story and a lesson learned).
I put the plug back in, and it kicked on the third try. I let it run for maybe five minutes or so and it fouled out again. I had changed the fuel, oil and cleaned the carb prior to this happening.

So what could be making my bike foul out so easily?

  • DeepSeaJohnny

Posted January 23, 2011 - 07:28 AM

#2

I'm going to pick up a new air filter tomorrow. I should have replaced it when I bought the bike.
Also the seals look really good. I'm very doubtful of oil leakage.

I'm also going to do some more cleaning, where the spark plug screws in. Its really dirty down there.

Visit the ThumperTalk Store for the lowest prices on motorcycle / ATV parts and accessories - Guaranteed
  • grayracer513

Posted January 23, 2011 - 08:28 AM

#3

A common error is to use the wrong plug. The bike needs a CR8E, or equivalent heat range. When people make the mistake of thinking a colder plug will help the engine run colder/better and substitute a CR9E, the bike will foul them left and right, because they aren't hot enough to keep themselves clean.

As to your spark plug, it may well just be worn out. Old plugs are easily fouled, and not easily cleaned. That said, the bike needs to be running right in order to keep the plug clean, too.

BTW, the air filter is intended to be cleaned in solvent or a strong detergent, dried and then to have air filter oil worked into it no less frequently than each second or third ride. They generally don't need to be replaced. The oil is important, because foam filters don't filter without it.

  • DeepSeaJohnny

Posted January 23, 2011 - 10:00 PM

#4

Thanks for the input on the CR9E spark plugs. That is what the original owner was using, but I have been using CR8E's. I will pick up a few of those.

  • fritzelman

Posted January 28, 2011 - 10:12 PM

#5

I was having the same problem with mine a few years ago. Turns out the fuel petcock was leaking. If the bike was warm I was fine, but as soon as I let it sit for 5 or 10 minutes I was stuck. New seal and bent the tension ring a little and havent had a problem since.





Related Content

Forums
Photo

YZ450F 03 Sparks driving me crazy by SirAttard


Dirt Bike   Make / Model Specific   Yamaha   YZ 400/426/450
  • 5 replies
Forums
Photo

yz250x vs 450 4t comparisons (preferably desert riding) needed by JakeNorthrupYZ450F


Dirt Bike   Make / Model Specific   Yamaha   Yamaha 2-Stroke
  • 9 replies
Forums
Photo

Is it worth it? (Cam and High compression piston) by macgi77


Dirt Bike   Make / Model Specific   Honda   CRF 150/230 F/L
  • Hot  36 replies
Reviews

Yamaha YZ450F 2017 by Chris.GVS


Yamaha YZ450F 2017
  • - - - - -
  • 0 reviews
Forums
Photo

100 hrs on 2014 yz450f, shim valves or replace them? by ttr230rider6


Dirt Bike   Make / Model Specific   Yamaha   YZ 400/426/450
  • Hot  79 replies
 
x

Join Our Community!

Even if you don't want to post, registered members get access to tools that make finding & following the good stuff easier.

If you enjoyed reading about "" here in the ThumperTalk archive, you'll LOVE our community. Come join ThumperTalk today!

The views and opinions expressed on this page are strictly those of the author, and have not been reviewed or approved by ThumperTalk.