Sisneros Speed Works products!
Posted 20 July 2010 - 05:12 PM
Sisneros Speed Works Super Start kit
Sisneros Speed Works "Free Power Mod" harness
Sisneros Speed Works high clearance choke assembly for the fcr-mx
Sisneros Speed Works pricing for RHC cams/valves,SSW springs
Sisneros Speed Works cap on coil conversion
Sisneros Speed Works single pull quick turn throttle
Sisneros Speed Works Manual Fan Override Switch
Sisneros Speed Works Crankshaft Inspection Plug
Sisneros Speed Works 50hp package
Sisneros Speed Works Cam Chain Service Kit
Sisneros Speed Works Oil Change kit
Sisneros Speed Works Engine Install / Top end Service Kit
Posted 21 July 2010 - 08:34 AM
Posted 21 July 2010 - 01:49 PM
And where's the link to some t-shirts?
Posted 21 July 2010 - 01:56 PM
Posted 21 July 2010 - 06:47 PM
Eddie Sisneros said:
//DOH...gotta burn the checkbook...
Posted 26 July 2010 - 09:17 AM
Posted 26 July 2010 - 11:08 AM
if there is demand i will produce it.
Posted 29 July 2010 - 06:41 AM
ive got throttle kits,start kits,cap/coil kits and chokes in stock and ready to ship!
Posted 02 August 2010 - 02:50 PM
A couple other ideas for those of us that hate chasing parts all over town or dealing with minimum order prices from Sudco:
- CE removal kit: a couple vaccuum caps and the proper PAJ or adj screw and maybe a pic or two.
- OEM jet/3x3 kit: Most everybody comes to you for jetting anyways, why not offer the OEM jets and needle/clip as a kit. I know it took me a couple trips to local places to find OEM jets and even then I was sold the wrong jets and had to go back to get the right style jets. Lost a whole Saturday running around chasing the right $5 jet. Throw in a 3" putty knife and a pic or two just to make it complete. Maybe even offer (as an option) a 'high altitude' jet with the parts if the buyer had freqent trips to a significant elevation.
- AP mod kit: For the dremel challenged or those that just dont want to grind on their own parts. Throw in some safety wire and a pic or two. I know the diaphram isnt cheap but maybe a core fee and swap out could work? Would be really cool if there was some sort of bushing that could be fitted to the plastic arm so help repair it or keep it from getting so egged out.
- TPS block off plate: I hate having that pig tail sitting there unplugged knowning it isnt doing anything. Maybe a milled out cover piece that would allow the TPS to be removed, the hole filled and the throttle shaft properly captured If it wasnt stupid expensive I'd like one just to clean up the carb area. I think Dr.Honda made one for a personal project once, looked cool.
I am sure there is some more cool stuff lurking in the SSW research lab that would sell if it saw the light of day. Sorry if this isnt the proper place for the ideas, just want to see SSW thrive!
Edited by ROMAD, 02 August 2010 - 03:08 PM.
Posted 04 August 2010 - 10:47 PM
Posted 06 August 2010 - 09:07 AM
Posted 07 August 2010 - 09:34 AM
My (your) 440 BB motor in my '00 plated E ran great at the Adv WMRS run last weekend.
So now the next step is address the suspension and the ergonomics.
Are you doing any suspension work/products?
I have to pull the front and rear suspension apart and put all new bushings,bearings,chains,sprockets etc in to replace my broken/worn out parts.
For ergonomics, I have to do something to get the bars up since I'm 6'7" and 280lbs. I recently added the offset DR Rizers and that helps alot but I need to do something about taller bars. Can you recommend a taller bar? Will your throttle kit work with rizers and a taller bar?
So my wishlist for parts from Eddie.
New throttle/cable that will work with taller bars/risers
Turkey baster coolent recovery system.
a fastener replacement kit... for all the common sizes of fasteners
bearing replacement kits
oil/air filters... and associated crush washers
and a list of services you offer... such as engine rebuilding
suspension services if any etc. now that you are in your new location.
Randy from Burbank
Posted 07 August 2010 - 10:40 AM
suspension,motors,complete bike builds,repair,etc etc.
my throttle will work with taller bars.
im not sure which is most popular bar bend currently.
i prefer the cr hi.
i will make another pinned thread with common services prices.
Posted 11 August 2010 - 07:04 PM
This is going on my Christmas list.
(I Am at 1200 ft)
PM me if you need to.
0 user(s) are reading this topic
0 members, 0 guests, 0 anonymous users