greyracer or others


7 replies to this topic
  • onelugnut

Posted November 02, 2009 - 06:36 PM

#1

I value you opinion. Thank you for the the help in the past.
Now I am going to replace the clutch plates in my boys 03 yz250 2smoke. Is there any thing else I should look at or just replace in the clutch. I know this is in the wrong section:busted:

  • rmx250rider

Posted November 02, 2009 - 09:08 PM

#2

procircuit clutch springs

  • onelugnut

Posted November 03, 2009 - 06:43 AM

#3

procircuit clutch springs


I dont see the advantage on a stock motor unless the price is the same as oem.
We ride mostly single track woods and desert. :smirk:

  • rmx250rider

Posted November 03, 2009 - 09:08 AM

#4

you asked for a opinion, so I gave one

Visit the ThumperTalk Store for the lowest prices on motorcycle / ATV parts and accessories - Guaranteed
  • KJ790

Posted November 03, 2009 - 09:22 AM

#5

Look at the basket and inner hub to see if they are notched at all. If you are only replacing the friction plates then lay the metal plates on a piece of glass and check for warping. If they are straight then rough them up with some sandpaper to get rid of any glaze and reuse them.

  • onelugnut

Posted November 03, 2009 - 12:50 PM

#6

you asked for a opinion, so I gave one


Sorry. I try not to sound like a d**K
I do thank you for your opinion

  • onelugnut

Posted November 03, 2009 - 12:52 PM

#7

Look at the basket and inner hub to see if they are notched at all. If you are only replacing the friction plates then lay the metal plates on a piece of glass and check for warping. If they are straight then rough them up with some sandpaper to get rid of any glaze and reuse them.


Sounds good. Thank you for the info

  • RJacks

Posted November 03, 2009 - 01:15 PM

#8

Also if the metal plates are steel and they show discoloring, (blue, or any heated look) replace them. If they are aluminum, replace if grooved. You also want to check the wear surface area, where the friction plate sits, on the pressure plate and inner hub to make sure they aren't worn out. A lip towards the inner edge will give it away.





Related Content

Forums
Photo

yz250x vs 450 4t comparisons (preferably desert riding) needed by JakeNorthrupYZ450F


Dirt Bike   Make / Model Specific   Yamaha   Yamaha 2-Stroke
  • 9 replies
Forums
Photo

2016 YZ450 by CaptainKnobby


Dirt Bike   Dirt Bike Technical Forums   Suspension
  • Hot  59 replies
Forums
Photo

Chubby dad, looking at bikes , First trip to the orange/black forum ! by Slow_ride


Dirt Bike   Make / Model Specific   KTM   250-530 EXC/MXC/SXC/XC-W/XCR-W (4-Strokes)
  • Hot  28 replies
Wiki
WR Camshaft Swap Info - last post by jamesm113

WR Camshaft Swap Info


Articles
  • 0 replies
Forums
Photo

Megabomb Fitment by 288yz450


Dirt Bike   Make / Model Specific   Yamaha   YZ 400/426/450
  • 1 reply
 
x

Join Our Community!

Even if you don't want to post, registered members get access to tools that make finding & following the good stuff easier.

If you enjoyed reading about "" here in the ThumperTalk archive, you'll LOVE our community. Come join ThumperTalk today!

The views and opinions expressed on this page are strictly those of the author, and have not been reviewed or approved by ThumperTalk.