04 450f problem


9 replies to this topic
  • Blank Stare

Posted December 13, 2006 - 11:09 AM

#1

I would do a search, but i don't know what this part is. I cant find it in the service manual that came with the bike either? On the head where the xhaust mounts up, directly above that There is a hole that i think use to have some sorta plug in it. There is noting there now and so oil came out of the hole. I found one picture in the manual section 4-82 that shows a bolt or plug there. What is it called and why is it not anywhere in the service manual. :thumbsup: HEEELLLLLPPPPPP

  • motobeck

Posted December 13, 2006 - 11:24 AM

#2

Sounds like the hole where they used to run the decompression mech. Check in the TT store for Decompression Plug. Hope this helps.

  • Blank Stare

Posted December 13, 2006 - 11:28 AM

#3

I was thinking that. I saw that TT has some special plug that is made not to blow out. but when i was reading the part description it was talking about a cam swap. I'll go back and check it out. What kinda of problem can occure from this plug blowing out? I think i caught it right after it happened.

  • Blank Stare

Posted December 13, 2006 - 11:31 AM

#4

Ok went back and reread the part description. looks like it is it!

  • motobeck

Posted December 13, 2006 - 11:33 AM

#5

Cool, that should solve your problems.

Visit the ThumperTalk Store for the lowest prices on motorcycle / ATV parts and accessories - Guaranteed
  • flintlock28

Posted December 13, 2006 - 04:39 PM

#6

The hole was there back when Yamaha used the manual decompression lever. When they went to auto-decompression, they didn't want to spend the money to re-tool the head (expensive), so they installed a rubber plug.

Sometimes it comes out, and that's what happened to you....order the new Aftermarket one from TT, and your problems are gone.

  • grayracer513

Posted December 13, 2006 - 04:55 PM

#7

When they went to auto-decompression, they didn't want to spend the money to re-tool the head (expensive), so they installed a rubber plug.

Their actual reason for this was to allow retrofitting manual decompression, and they offered a complete kit to accomplish that.

They designed it out of the '06 head, since almost no one wanted to add the kit.

  • flintlock28

Posted December 13, 2006 - 05:03 PM

#8

Oops, my bad....Grayracer is correct. I wrote that with my three year old and 4 month old crying, and had a Brain fart.

  • Blank Stare

Posted December 13, 2006 - 05:17 PM

#9

Their actual reason for this was to allow retrofitting manual decompression, and they offered a complete kit to accomplish that.

They designed it out of the '06 head, since almost no one wanted to add the kit.


i thought i already had that. the lever above the clutch lever

  • grayracer513

Posted December 13, 2006 - 07:15 PM

#10

It's time for you to brush up on your bike a bit. That's the hot start lever.





Related Content

Forums
Photo

Should I buy this bike? help....... by Numsa Hul


Dirt Bike   General Dirt Bike Forums   What bike should I buy?
  • * * * * *
  • 10 replies
Wiki
WR Camshaft Swap Info - last post by jamesm113

WR Camshaft Swap Info


Articles
  • 0 replies
Forums
Photo

Snake pit oct 30th by The Anvil


Dirt Bike   Dirt Bike Regional Discussion   California
  • Hot  293 replies
Forums
Photo

Is it worth it? (Cam and High compression piston) by macgi77


Dirt Bike   Make / Model Specific   Honda   CRF 150/230 F/L
  • Hot  36 replies
Forums
Photo

YZ450FX OR YZ450F by MESSMAKER


Dirt Bike   Make / Model Specific   Yamaha   YZ 400/426/450
  • Hot  30 replies
 
x

Join Our Community!

Even if you don't want to post, registered members get access to tools that make finding & following the good stuff easier.

If you enjoyed reading about "" here in the ThumperTalk archive, you'll LOVE our community. Come join ThumperTalk today!

The views and opinions expressed on this page are strictly those of the author, and have not been reviewed or approved by ThumperTalk.