XR600R bars?


5 replies to this topic
  • Terez

Posted October 10, 2006 - 04:55 PM

#1

Will be repalcing the bars on my 90XR600R...way too low.

I am wondering how tall can I go with my stock cables/lines?

It doesn't appear I can go more than a couple of inches?

I am leaning towards Pro tapers in the tallest bend they have.
The KX high looks to be the tallest @ 4.25in rise.
The only other bars significantly taller are the ATV low/mid/high.
Will these fit...the ATV low? 5.5in rise.
They seem to flare up from flat too....is this comfortable?

What about bar risers?
Are there risers available that bolt between my stock clamps and the bars?

I am 6ft and like to ride standing a lot.

Thanks

  • rebelventurer

Posted October 10, 2006 - 06:28 PM

#2

try www.rswracing.com they have a nice triple clamp from billett with an inch rise on the bar mounts also they are available for 7/8" or 1 1/8" bars around $120. RSW also has a nice fork brace $80 half of what others sell for. Also try protapers in the Travis Pastrana bend I think they have about 5" rise and no upturned ends and are wider than the atv bars. You can find them on ebay att powersinc ebay store the 1 1/8" contour bars are $62. good luck. Oh, check my garage I have these same parts on my bike.

  • Boston Mangler

Posted October 10, 2006 - 06:36 PM

#3

What about bar risers?
Are there risers available that bolt between my stock clamps and the bars?


Yes, i am in the same boat as you and came across these:

http://www.roxspeedf...i?subcat_id=268

Anyone try these?

I am currently looking at the best fit for me as well.

Visit the ThumperTalk Store for the lowest prices on motorcycle / ATV parts and accessories - Guaranteed
  • rebelventurer

Posted October 10, 2006 - 06:48 PM

#4

Mangler, those are scary looking to me, and $75 just put up the other $50 and get the rsw clamp. It will give you a good strong foundation to mount your bars to, them things just give more leverage on the week cast aluminum clamp. SCARY!

  • Boston Mangler

Posted October 10, 2006 - 06:51 PM

#5

Yeah, i agree. Its a great idea in theory, but the more things to loosen up and slip, the worse off you are! :devil:

And yes, there would be a ton of leverage on those things in "not so ideal" areas of the machining!

  • rebelventurer

Posted October 10, 2006 - 06:54 PM

#6

Glad you see the light I want everyone to be safe, even the guy that doesnt use locktite.





Related Content

Forums
Photo

XR650L super moto wheels by greggkklee


Dirt Bike   Make / Model Specific   Honda   XR600/650
  • Hot  28 replies
Reviews

Honda XR650L 2017 by Chris.GVS


Honda XR650L 2017
  • - - - - -
  • 0 reviews
Forums
Photo

ignitech programmable XR650L CDI by brianhare


Dirt Bike   Make / Model Specific   Honda   XR600/650
  • Hot  60 replies
Wiki
Want to add a kickstart to your XR650L?  Here's how - last post by clc3251

Want to add a kickstart to your XR650L? Here's how


Articles
  • 0 replies
Forums
Photo

93 xr650l Restoration Project by Zigster


Dirt Bike   Make / Model Specific   Honda   XR600/650
  • 17 replies
 
x

Join Our Community!

Even if you don't want to post, registered members get access to tools that make finding & following the good stuff easier.

If you enjoyed reading about "" here in the ThumperTalk archive, you'll LOVE our community. Come join ThumperTalk today!

The views and opinions expressed on this page are strictly those of the author, and have not been reviewed or approved by ThumperTalk.