Pismo Beach, NOW RUST!!! newb


6 replies to this topic
  • EastBayThumper

Posted September 10, 2006 - 09:51 PM

#1

I have a pretty new 2005 YZ450F.

I am still learning how to properly maintain it.. Today was my first time removing my chain.. I am cleaning it in Kerosine. I am going to remove my shift linkage and give it a lube as well as my front tire....

What can I do to get rid of the nasty rust in that bolt.. and keep my sprockets nice and clean??

Doesn't seem like Simple Green 50/50 will be enough.. Any info/links will be appreciated!!!

Thanks.
Posted Image

  • 01yz426

Posted September 10, 2006 - 09:54 PM

#2

I always kinda soak each bolt 'n' nut that I take off in some kind of WD-40 type chemical... Or some Metal Parts Cleaner, they seem to come out clean and also screw back in a whole lot better.... I do about 90% sand riding and I know that those bolts can take a beating so I'd just get some Metal Parts Cleaner and soak em... Hope this helps...

  • barch88

Posted September 11, 2006 - 09:32 AM

#3

PB Blaster

Visit the ThumperTalk Store for the lowest prices on motorcycle / ATV parts and accessories - Guaranteed
  • w00ht

Posted September 11, 2006 - 05:35 PM

#4

PB Blaster


Best stuff ever, works great to loosen all bolts and is a much better protective lube than WD40. Just use it in moderation and keep it away from things that get really hot. If not you'll have a wonderful smelly bike as the chemicals burn away.

  • David37

Posted September 11, 2006 - 08:11 PM

#5

IMO the best technique to keep your bike from rusting is stay away from the salt air and sand. I would clean your chain with WD40 and then lube with chain lube. Buy a tube of anti-seize and put on the threads of your chain adjusters where they thread into the swingarm and on the nut and axle bolt. I would clean and lube with water proof grease both the front and rear axles. The sand also tends to get inside your rear suspension linkages and bearings causing premature wear.

  • Ga426owner

Posted September 12, 2006 - 06:37 AM

#6

That bolt will always have rust on it - spray it with lube to make it look better...and stay out of any salt water...or tear it (linkage) completely down afterwards clean and relube

  • MX1967

Posted September 12, 2006 - 09:51 AM

#7

Pismo is a beautiful place but I will never take my bike there. We spent 3 days there a few years ago & just took the quads. I spent so much time & WD 40 after I got home just to stop the rust. My new toolbox buckles even rusted just sitting in the back of my truck :thumbsup: There's really nothing you can do except maybe rinse the bikes off at night & then cover them up or keep them in the toy hauler. Perhaps next time I go one of you guys will be nice enough to let me borrow on of your bikes...I got lots of WD 40!!!!!!!!!!!





Related Content

Forums
Photo
Motocross

Thinking about Yamaha 250... by Arctic Pride


Dirt Bike   Special Interest Forums   Pro Racing
  • Hot  491 replies
Forums
Photo

Michigan Motocross Tires by 288yz450


Dirt Bike   Dirt Bike Regional Discussion   North
  • 1 reply
Forums
Photo

yz250x vs 450 4t comparisons (preferably desert riding) needed by JakeNorthrupYZ450F


Dirt Bike   Make / Model Specific   Yamaha   Yamaha 2-Stroke
  • 9 replies
Forums
Photo

Chubby dad, looking at bikes , First trip to the orange/black forum ! by Slow_ride


Dirt Bike   Make / Model Specific   KTM   250-530 EXC/MXC/SXC/XC-W/XCR-W (4-Strokes)
  • Hot  28 replies
Forums
Photo

2016 YZ450 by CaptainKnobby


Dirt Bike   Dirt Bike Technical Forums   Suspension
  • Hot  59 replies
 
x

Join Our Community!

Even if you don't want to post, registered members get access to tools that make finding & following the good stuff easier.

If you enjoyed reading about "" here in the ThumperTalk archive, you'll LOVE our community. Come join ThumperTalk today!

The views and opinions expressed on this page are strictly those of the author, and have not been reviewed or approved by ThumperTalk.