Flywheel Installation, help needed!



6 replies to this topic
  • Gunner_V

Posted March 19, 2002 - 01:03 AM

#1

Does anyone know the best way to hold onto your flywheel when you are taking your flywheel nut off without having to buy a special tool? I tried leaving the bike in gear and blocking the wheel from spinning, but it didn’t work. Help! I have a Ty Racing 10 oz. Flywheel weight sitting in my toolbox because I can’t install it!

  • Mark_UK

Posted March 19, 2002 - 03:26 AM

#2

stick a screw driver in and jam the counter balence wieght

  • Tommy_Gun

Posted March 19, 2002 - 05:45 AM

#3

Even though you have a Ty Davis flywheel, get one of these engine lockup tools from Steahly Off-Road at: http://www.steahlyof...log/tools.shtml
They work excellent.
-Tom

Visit the ThumperTalk Store for the lowest prices on motorcycle / ATV parts and accessories - Guaranteed
  • mor

Posted March 19, 2002 - 05:56 AM

#4

i used air driven wrench.

  • wylie1

Posted March 19, 2002 - 06:10 AM

#5

I used a pneumatic impact to remove the flywheel nut. To get it back on I bought a special oil filter wrench from Napa auto parts for $6.00. The oil filter wrench looks like a piece of nylon strap with a square piece of metal tubing hooked on the side of it. I put it around the entire flywheel to hold the flywheel in place and was able to torque the flywheel to specification. Hope this helps.

James

[ March 19, 2002: Message edited by: wylie1 ]

  • wylie1

Posted March 19, 2002 - 06:23 AM

#6

Here is the Napa tool.
http://www.napaonlin...6&usrcommgrpid=

and motion pro has a really good one.

http://www.motionpro...icetools_3.html

  • yankee

Posted March 21, 2002 - 03:52 AM

#7

I use a motion pro clutch holding tool. I got it for $30 from the local dealer. You can use this tool for the clutch basket, primary gear, flywheel, and front sprocket.

If you have access to an impact wrench you can use that instead.

If you have the right crankcase cover off than you can just stick a small piece of aluminum between the primary and clutch basket gears. This will stop the crank from moving.

[ March 21, 2002: Message edited by: yankee ]





Related Content

Forums
Photo

2016 YZ450 by CaptainKnobby


Dirt Bike   Dirt Bike Technical Forums   Suspension
  • Hot  59 replies
Forums
Photo

Michigan Motocross Tires by 288yz450


Dirt Bike   Dirt Bike Regional Discussion   North
  • 1 reply
Forums
Photo
Motocross

Thinking about Yamaha 250... by Arctic Pride


Dirt Bike   Special Interest Forums   Pro Racing
  • Hot  491 replies
Wiki
WR Camshaft Swap Info - last post by jamesm113

WR Camshaft Swap Info


Articles
  • 0 replies
Forums
Photo

Chubby dad, looking at bikes , First trip to the orange/black forum ! by Slow_ride


Dirt Bike   Make / Model Specific   KTM   250-530 EXC/MXC/SXC/XC-W/XCR-W (4-Strokes)
  • Hot  28 replies
 
x

Join Our Community!

Even if you don't want to post, registered members get access to tools that make finding & following the good stuff easier.

If you enjoyed reading about "" here in the ThumperTalk archive, you'll LOVE our community. Come join ThumperTalk today!

The views and opinions expressed on this page are strictly those of the author, and have not been reviewed or approved by ThumperTalk.