Triple Clamp recommendations

4 replies to this topic
  • OnThePipe

Posted January 26, 2002 - 10:28 PM


Anyone have any recommendations on aftermarket Triple clamps for oversize bars? The last two crashes (and bent 7/8" bars) have tempted me to bite the bullet and purchase the aftermarket clamps and 1 1/8" bars. I'm looking at Applied and/or Pro-Taper unless someone has some totally negative feedback on these units.

  • scottzx7rr

Posted January 26, 2002 - 12:44 PM


I have used the Applied Tripleclamp setup with good luck. I am currently running the Scott's Setup for the steering damper. But before I started using the damper I loved it because it has a forward setting that allowed my to move my handlebars about 1 inch forward. Opened up the Cockpit nicely.

Visit the ThumperTalk Store for the lowest prices on motorcycle / ATV parts and accessories - Guaranteed
  • 426_Pilot

Posted January 27, 2002 - 05:38 AM


Here is my post from another topic, but it applies here. I love this triple clamp:

I'm 6'2" and 215lbs. and have an '01. I put on the Oberg Sports triple clamp which has five different positions - 5mm aft, stock,5mm forward, 10mm forward, 15mm forward. Of course, I run 15 forward which puts the bars over the top of the forks. I have the stock (oversize) mounts, but Oberg makes taller mounts and I think when you order the taller mounts the also send the stock.
This is a very trick piece of equipment. I ordered through Moto Sport Outlet and they have package deals on Clamp/Bars. I went with the Renthal Fat Bar, CR High bend. One item of note, I spoke with someone from Oberg when I was researching this clamp and I was told that the mounting angle of the Yamaha clamp was something like 27 degrees. This is significant because as you move the mount forward you get some additional rise. The forward-most position is 9mm taller than aft. You can check the triple clamp out at:

Oberg Sports

  • 426_Pilot

Posted January 27, 2002 - 05:41 AM


Sorry, I screwed something up on the Oberg link, here it is:

Oberg Sports

  • freestyle111

Posted January 27, 2002 - 06:43 AM


i have azonics tripleclamp with azonics doublecross bars[cr hibends].triple clamp is similar to scotts 5mm or 12mm forward 10mm taller. doulblecross bars speak for themselves.if you crash hard enough to bend them you probably wont care youll be in so much pain.renthals new tripleclamp is pretty awesome

Related Content


Should I buy this bike? help....... by Numsa Hul

Dirt Bike   General Dirt Bike Forums   What bike should I buy?
  • * * * * *
  • 10 replies

Yamaha YZ450F 2017 by Chris.GVS

Yamaha YZ450F 2017
  • * * * * *
  • 1 review
  • Last review by Tommyk_55
  • On January 15, 2017

Chubby dad, looking at bikes , First trip to the orange/black forum ! by Slow_ride

Dirt Bike   Make / Model Specific   KTM   250-530 EXC/MXC/SXC/XC-W/XCR-W (4-Strokes)
  • Hot  28 replies

James Stewart back on a YZ450F by YamaLink

Dirt Bike   Special Interest Forums   Pro Racing
  • Hot  47 replies

05 yz450f not fast enough by RedeyeYZ

Dirt Bike   Make / Model Specific   Yamaha   YZ 400/426/450
  • Hot  38 replies

Join Our Community!

Even if you don't want to post, registered members get access to tools that make finding & following the good stuff easier.

If you enjoyed reading about "" here in the ThumperTalk archive, you'll LOVE our community. Come join ThumperTalk today!

The views and opinions expressed on this page are strictly those of the author, and have not been reviewed or approved by ThumperTalk.